热门帖子

2011年12月23日星期五

Wooden doors and windows should be noted that acceptance of what issues

Wooden doors and windows should be noted that acceptance of what issues

Hand percussion automatic doors doors and windows set side panels, if the issue of empty drums, it shows no mat Blockboard other grass-roots bottom plates, should be dismantled and redone.
1, appearance to appearance: The surface coating of wood windows and doors to be smooth, bright, no flow fall, bubbles, wrinkles and other defects, there is no corrosion points, dead sections, broken remnant; package sets of wood doors and windows and doors and windows should be wood fan, color coordination, color decorative panels and molding is not large, should be the same species.
2, door and window fans to the Founder, does not warpage, doors and windows just to fan into door frames, door frames and is consistent with: if doors and windows box fan with a large gap, mainly because not allowed to install or repair when the plane door and window frames is not perpendicular to the ground, remove the fan can be re-dig repair doors and windows; such as door frames are not vertical, plate gasket should be looking at the box straight.
3, hinge to automatic door position accurately, securely installed: If you did not hinge on the positive, will lead to sets of doors and windows do not coincide with the box fan, doors and windows switches is not smooth. Each hinge can be unscrewed a screw, then adjust the doors and windows fan and box fit, adjust and then repair and correct all the screws tightened. If the short hinge screws or nails on the screws look into, not tighten the screws, or screws ramp, fight fans will visit leading to doors and windows. Should be replaced right screws, the screws must be straight, screw should screw into the 1 / 3, and the rest to be screwed into it.
4, door open, lock to be smooth, locks in the doors and door frames to fit on two parts: the lock pretend to be inappropriate, not freely switch will cause the doors. Latch plate should be removed with a chisel repair the tongue groove, adjust the position of the mouth and then install the door latch. In addition, the direction of the door opening must meet the requirements.
5, doors and windows which have a set of base material: window cover made with MDF Blockboard or, should the first grass-roots grass-roots level keel plate to the window frame, and then nail the line; Door frame made of wood is preferred, the planing , planing straight, and then installed on the wall molding assembly is then covered with grass-roots board and veneer. Hand percussion doors and windows set side panels, if the issue of empty drums, it shows no mat Blockboard other grass-roots bottom plates, should be dismantled and redone.

Wireless transmitter module works Detailed

Wireless transmitter module works Detailed

DF data transmitter automatic doors module operating frequency is 315M, the use of SAW SAW resonator frequency stabilization, high frequency stability, when the ambient temperature
varies between -25 to +85 degrees, the frequency drift of only 3ppm / °. Particularly suitable for a collection of multiple wireless remote control and data
transmission systems. SAW resonator frequency stability after the crystal, and general LC oscillator frequency stability and consistency is poor, even with high-
quality fine-tuning automatic door capacitance, temperature changes and vibration is also difficult to ensure that no frequency has been tuned will shift.
DF transmitter module has not established a coding circuit, and an increase of a data modulation transistor Q1, this structure makes it easy and other fixed
coding circuit, rolling code circuitry and microcontroller interface, without having to consider coding circuit voltage and output The size of the signal amplitude
value. Such as integrated circuits with the PT2262 with other codes when connected directly to their data output pin to the first 17 data input of the DF can be.
DF data module with a wide operating voltage range 3 ~ 12V, when the voltage is essentially the same transmission frequency changes, and the transmitter module
supporting the receiver module can be stable without any adjustment to receive. When the transmitter voltage is 3V, open to the transmission distance of about 20 to 50
meters, less transmission power, when the voltage is 5V at about 100 to 200 meters, when the voltage is 9V about 300 to 500 meters when firing voltage is 12V, the
optimum operating voltage, and has good emission results, emission current 60 mA, open to 700 to 800 meters transmission distance, transmission power of 500 mW. When
the voltage is greater than l2V increased power consumption, effective radiated power is no longer significantly increased. The module is characterized by relatively
large transmission power, transmission distance is far more suitable to communicate under adverse conditions. The best selection of 25 cm long antenna wire, the best
long-distance transmission can be erected, because the transmission of radio signals received many factors, it is generally practical distance from the nominal only
20% or less, this point needs to consideration when developing attention.
DF data module using ASK modulation method to reduce power consumption when transmitting data signals to stop when the current drops to zero, the data signal
transmitter module with the DF input resistance or can be connected directly rather than using capacitive coupling, or DF transmitter module will not work. Data should
be close to the actual work of DF data module voltage to obtain higher modulation effect.
DF launch best vertical launch modules mounted on the edge of the motherboard, more than 5mm should be left around the device to the distribution parameters from
IMPACT. DF module transmission distance and signal frequency and amplitude modulation, transmitter voltage and battery capacity, transmitting antenna, receiver
sensitivity, sending and receiving environment. Generally the maximum emission from the open area about 800 meters, there are obstacles in the case, the distance will
be shortened, due to radio signal transmission in the refraction and reflection will form some of the dead and the unstable region, different transceiver environment
will be different transceiver distance.

Wings automatic revolving door security

Wings automatic revolving door security

Wings automatic automatic door revolving door security revolving door for the current general security risks exist, the use of back sliding mechanism to increase the anti-collision pinch of that function.
Ad hoc with one-touch speed rotary switch on the door wing rotation, through the door switch can shift from the normal rotating speed rotation state.
Wing and show me the door 8mm safety glass transparent, curved walls 5 +5 m transparent curved laminated safety glass with. Door and door wing tip and the lower fixed column are set on the buffer automatic doors material, full access to ensure pedestrian safety.

A Division of Door Services Corporation

A Division of Door Services Corporation

Automatic Door Enterprises has been in the business of supplying and installing automatic doors since April 1, 1979. We are a distributor of automatic entrance systems including Industrial Doors, Revolving Doors, Swing Operators and Sliding Entrance Systems. We have been the market leader in access solutions as well as specialty applications for many years. The reason we have such a loyal clientele is due to our dedication and product reliability. From the original site survey to routine repairs, our goal is to exceed all expectations when it comes to "Customer Service." If there is any other information you may need, please feel free to contact us. automatic door Enterprises services all of Pennsylvania, New Jersey, Delaware and the Eastern Shore of Maryland. Our Company sells automatic & manual door systems from Horton Automatics, KM Systems, Record-USA, Chase, Saino, Brookfiled and Boon Edam. These systems include automatic swing doors, automatic sliding doors, automatic revolving doors, manual revolving doors, security revolving doors, automatic industrial doors, pneumatic sliding and swinging doors and automatic fire doors. We also offer a complete line of parts and service through our sister company Advanced Door Service.